ANPR questions & answers
Answers for the systems around number-plate recognition.
Practical, vendor-neutral guidance for cameras, NVRs, VMS platforms, access control and metadata integrations.
These are general industry answers, not product support. Setting up ANPR Edge? Read the camera connection guide.
56 answersin VMS
Why is my Milestone XProtect LPR server CPU usage hitting 100%?
Check the installed LPR release, the camera workload and the recognition settings before changing codecs. High LPR server CPU usually means the server is decoding and analysing more video than it can handle, and the codec advice depends on the release: the 2024 R2 manual recommends JPEG, while the 2025 R2 manual recommends H.264, advises against JPEG and does not support H.265 for LPR.
XProtect LPR Administrator Manual 2024 R2 (page 29); XProtect LPR Administrator Manual 2025 R2 (pages 38 and 41)
Why is my Avigilon ACC/Unity LPR watch list CSV import failing?
Avigilon Unity and ACC require a very specific CSV formatting structure to successfully import a database of watch list plates. The most common cause of complete import failure is omitting the mandatory "Minimum Confidence" column, which tells the VMS how strict the OCR match must be before triggering a security rule.
Avigilon Unity Video Client User Guide - LPR Watch Lists
Why are Wisenet WAVE LPR bookmarks playing back at the wrong time?
If clicking an LPR event bookmark in the Wisenet WAVE client jumps the video playback to a timestamp completely devoid of a vehicle, you are experiencing a severe clock synchronization mismatch. The VMS server and the edge cameras are operating on different clocks.
Hanwha Vision: Synch issue between playback time and camera time
Why does the Wisenet WAVE AI Plugin freeze or drop streams?
When utilizing the WAVE AI Plugin, adjusting the "AI Tracking Speed" too high exponentially increases the computational burden on the server. Setting the tracking speed to "Very Fast" for vehicles can severely reduce the number of AI streams the server can handle, leading to dropped frames and system freezing.
WAVE: How to Setup the AI Plugin
Why does XProtect LPR ignore plates that look readable on screen?
The character-height range may exclude them.
Milestone: Configuring cameras for LPR
Why does XProtect recognize only fragments of a number plate?
Obstructions and an insufficient partial-recognition time span can cause incomplete results.
Milestone: Configuring cameras for LPR
Why does XProtect LPR reject a foreign plate but read local plates?
The relevant country or region module may not be active.
Milestone: Country modules
Why does XProtect’s generic country module fail to identify a plate’s country?
Generic symbol recognition is not equivalent to country identification.
Milestone: Country modules
Why does an XProtect match-list alarm fail after the plate is recognized?
A list match needs an associated event to trigger the intended workflow.
Milestone: Match lists, 2026 R1
How do I watch for an XProtect plate when one character is unknown?
Match lists support question-mark wildcard patterns.
Milestone: Match lists, 2026 R1
Why can’t I add another LPR camera even though XProtect records its video?
LPR needs its own camera license.
XProtect LPR licenses, 2026 R1
Why can’t I enable another XProtect country module?
You may have used the available country-module licenses.
XProtect LPR licenses, 2026 R1
Why are known XProtect LPR events missing from my search?
Search filters may exclude the events.
Milestone: Viewing LPR related content, 2026 R1
Why did importing a new XProtect match list remove existing plates?
The import may have used Replace instead of Add.
Milestone: Viewing LPR related content, 2026 R1
Why did an old XProtect LPR component stop writing logs after a Log Server upgrade?
A historical authentication change can block older components.
Milestone: Managing server logs
Why can’t I install Wisenet Road AI on an ordinary Hanwha camera?
Road AI requires supported cameras supplied with the application.
Hanwha: Configure Road AI and integrate with WAVE
Why does a new Wisenet Road AI camera struggle with plates outside the USA?
Check its selected recognition region.
Hanwha: Configure Road AI and integrate with WAVE
Why does only one of several Road AI cameras send plate text to a Wisenet NVR?
Check each text integration’s port and channel mapping.
Hanwha: Road AI camera event setup for NVRs
Why do Road AI plate records appear under the wrong Wisenet NVR camera?
Check the text receiver’s channel assignment.
Hanwha: Road AI camera event setup for NVRs
Why do WAVE Road AI bookmarks contain plate numbers but no vehicle details?
Automatic bookmarks and Generic Events carry different information.
Hanwha: Generic events, bookmarks and rules with RoadAI
Why does a Road AI whitelist event arrive in WAVE without triggering the expected action?
Check the Generic Event description filter.
Hanwha: Generic events, bookmarks and rules with RoadAI
Why did Road AI or RoadWatch bookmarks stop after upgrading WAVE to 5.1?
An older integration may use the previous bookmark API.
Hanwha: Bookmarks no longer created after WAVE V5.1 upgrade
Why does changing the camera’s relay pulse duration fail to keep an ANPR barrier open longer?
The ANPR application can override the camera setting.
Hanwha: Increase pulse time for barrier operation
Why does RoadWatch fail to send LPR data to WAVE when the camera name contains spaces?
Check the documented RoadWatch camera-name issue.
Hanwha: RoadWatch LPR data in WAVE
Why does RoadWatch connect to WAVE video but fail to deliver plate events with my credentials?
Check the authentication configuration used by the application.
Hanwha: RoadWatch LPR data in WAVE
Why does a SharpV G3 fail when powered by an older SharpV PoE injector?
Verify its power source against the G3 requirement.
Genetec: SharpV cannot read plates at night
Why do SharpV HTTP events work but HTTPS events fail?
Check TLS certificate validation and endpoint trust.
Genetec: Configure SharpV HTTP/HTTPS extension
Why did SharpV anonymized plate identifiers change after a configuration change?
Check whether the anonymization salt changed.
Genetec: Configure SharpV HTTP/HTTPS extension
Why are only high-confidence SharpV reads reaching my HTTP receiver?
The extension may apply a confidence filter.
Genetec: Configure HTTP/HTTPS extension
Why did queued SharpV HTTP reads disappear when I disabled offline retention?
That setting can delete retained reads.
Genetec: Configure HTTP/HTTPS extension
Why does SharpV 14.5 Multi extension resend stored reads to Security Center but not to my HTTP server?
The documented Multi extension has different outage behaviour for its destinations.
Genetec: Configure multiple SharpV extensions
Can a SharpV 14.6 camera send different recognized plate datasets to different extensions?
Its extensions share the same ALPR data.
Genetec: About SharpV extensions
Why does AutoVu record NOPLATE events even though vehicles are being counted?
A vehicle trigger can occur without a readable plate.
Genetec: Investigating NOPLATE reads
Why does editing an AutoVu NOPLATE read change its confidence to 100?
That is the documented behaviour of a manual correction.
Genetec: Investigating NOPLATE reads
Why does SharpV read parked vehicles beyond my intended capture lane?
Check character-height limits and the recognition area.
Genetec: Low ALPR read rates or poor quality reads
Why did a legacy Patroller hotlist stop updating after its USB drive or source location changed?
The configured source path may no longer exist.
Genetec: Hotlist or permit list does not update automatically
Why does replacing a legacy Patroller hotlist file with new content fail to refresh the list?
Check the incoming file’s modification timestamp.
Genetec: Hotlist or permit list does not update automatically
Why does adding a plate to a Security Center hotlist fail to create hits for older reads?
Hotlist edits affect new reads; retrospective matching is separate.
Genetec: Editing hotlists
Why are AutoVu hotlist hits live on my map but ordinary plate reads are not?
The Web App displays them differently.
Genetec Web App: Monitor ALPR events on maps
What should I collect before reporting an AutoVu component connection failure?
Capture the component’s status and diagnostics.
Genetec: Checking AutoVu component status
Why does Patroller ignore older reads after I add a new wanted plate?
Past read matching may be disabled or its look-back period too short.
Genetec: Operation — Hotlists tab
Why doesn’t Patroller generate a second consecutive hit for the same plate?
Allow consecutive hits may be switched off.
Genetec: Operation — Hotlists tab
Why does an HTTP Generic Event reach Nx Witness without triggering my alarm rule?
Event reception and rule matching are separate.
Network Optix: Create HTTP Generic Events
Why does a plate event create a bookmark on the wrong Nx Witness camera?
Check the device association sent with the event.
Network Optix: Create HTTP Generic Events
Why is Nx Witness plate or analytics search slow even when video playback is smooth?
Analytics metadata has its own storage workload.
Network Optix: Analytics usage limitations
Why does moving a camera between Nx Witness servers complicate historical analytics search?
Its metadata can span servers.
Network Optix: Analytics usage limitations
Why doesn’t a partial plate wildcard search behave as expected in Nx Witness?
Search syntax depends on the search area and field.
Network Optix: Search syntax guide
Why does a recognized plate fail to match an Nx Witness attribute search?
Check the attribute name and query syntax.
Network Optix: Search syntax guide
Why does my Nx analytics plugin create hundreds of duplicate objects for one vehicle?
The plugin may create a new object for every frame.
Network Optix: Metadata SDK implementation best practices
Why can my Nx plugin draw a plate box but users cannot search the plate text?
A bounding box alone does not supply searchable plate attributes.
Network Optix: Metadata SDK implementation best practices
Why is plate recognition unavailable on my Alta panoramic camera?
The cited Alta setup guide excludes panoramic cameras.
Avigilon Alta: configure an LPR camera
Why does Alta detect vehicles but miss plates when several cars occupy one LPR zone?
The zone may cover too much traffic.
Avigilon Alta: configure an LPR camera
Why does my H4 LPC scene look very dark even during daylight?
This dedicated capture camera is sensitive to IR rather than visible light.
Avigilon H4 LPC / ACC LPR 6 site design guide
Why does increasing my ACC LPR analysis rate fail to improve recognition?
Check the camera’s actual frame rate.
Avigilon H4 LPC / ACC LPR 6 site design guide
Why does Avigilon Player return no results for a partly remembered plate?
Check the search’s Match percent.
Avigilon Player 7 user guide
Why does my ACC watchlist generate too many false plate alerts?
Review the per-entry Minimum Confidence and its version-specific meaning.
ACC integration guide for Gallagher Command Centre
Didn’t find your question?
Type it below. We’ll search the existing answers first, and if none of them fit you can send it to us.